Works with 2.7V/3.3V/5.0V logic systems, 4bit/8bit/16bit/32bit micro-controllers. it EVEN works stand-alone.
Support serial (Hardware or Software): UART, I2C and SPI, set by the jumpers on PCB, support all four SPI mo.
7 fonts and graphic engine embedded, touch screen and flash chip drivers embedded(if touch screen or 2 to 16MB flash chip installed), custom fonts can be downloaded to the module's flash.
High level commands set (61 commands total) are easy to remember and understand, eg.: send 5 bytes: "CCabc" will draw a ratio=c pixels circle at coordinate (a,b) on the screen; 5 bytes "DNALL" will put the module to sleep mode(<0.1mA), and more...
OLED is the newest display technolegy in market now, as same as the modern OLED TV (Not LED TV, it use LCD with LED backlight), it can emitting light by it self, no backlight needed, so it's good for battery powered electronics.
Specification:
Power Supply: 2.2V to 9V
Power consumption: maximum 40mA at 5V when all dots light on (Display White color)
Communication mode: UART/I2C/SPI, detect your setting automatically
Receiving buffer: 2048 bytes
Work with all microcontroller and microprocessor
Communication signal can work on 2.1V to 5V TTL and CMOS
// Communication set up command
* "SB":Baud (ascII bytes end with 0x00/0x0A/0x0D) -- set UART Baud Rate
* "SI2CA":Address(1 byte <127) -- Set I2C address, default address is:0x27
* "DC":1/0(1byte) -- set config display on/off, if set to 1, displayer will display current commucation setting when power on
// Text Function command
* "CL": -- Clear screen--OK
* "CS":1/0 (1 byte)-- Cursor on/off
* "TP":x(1 byte) y(1 byte) -- set text position
* "TT":string(bytes) end with 0x00/0x0A/0x0D -- display string under regular mode
// Graphic function command
* "GP":x(1byte) y(1byte) -- set current graphic position
* "DM":"C/!/~/&/|/^"(ASCII 1byte) -- set drawing mode--C="Copy",! and ~ = "Not", & = "And", | = "Or", ^ = "Xor"
* "SC":1/0 (1byte) -- set draw color--only 1 and 0
* "LN":x0(1byte) y0(1byte) x1(1byte) y2(1byte)--draw line from x0,y0 to x1,y1,set new pot to x1,y1
* "LT":x(1byte) y(1byte) -- draw line from current pos to x,y
* "CC":x(1byte) y(1byte) ratio(byte) -- draw circle at x,y with ratio
* "DP":x(1byte) y(1byte) Color(1byte) -- draw a pixel--OK
* "DR":x0(1byte) y0(1byte) x1(1byte) y2(1byte)--draw rectangle, top-left:x0,y0; right-bottom:x1,y1
* "FR":x0(1byte) y0(1byte) x1(1byte) y2(1byte)--draw filled rectangle, top-left:x0,y0; right-bottom:x1,y1
*/
int main(int argc, char **argv)
{
int fd;
char *fileName = "/dev/i2c-1"; // Name of the port we will be using, Rasberry Pi model B (i2c-1)
int address = 0x27; // Address of I2C device
char buf[100];
if ((fd = open (fileName, O_RDWR)) < 0) { // Open port for reading and writing
printf("Failed to open i2c port\n");
exit(1);
}
if (ioctl(fd, I2C_SLAVE, address) < 0) { // Set the port options and set the address of the device
printf("Unable to get bus access to talk to slave\n");
exit(1);
}
if (argc>1)
{
sprintf(buf,argv[1]);
//printf("%s %d %s\n",buf,strlen(buf),buf[strlen(buf)]);
if ((write(fd, buf, strlen(buf)+1)) != strlen(buf)+1) {
printf("Error writing to i2c slave\n");
exit(1);
}
} else {
printf(" Simple tool to send commands to Digole graphic adapter\nexamples:\n");
printf(" rpi_lcd \"CLTTHello Word\" - Clear the screen (CL) and prints \"Hello Word\" (TT)\n");
printf(" rpi_lcd \"CC002\" - Draws a cirle at x=30 (0), y=30 (0) with a radio of 32 (2)\n"); //not for Character LCD
}
return 0;
}
iDigole Buyer
e-Care 
Guarantee 
Download 
Contact us 
Forum 
Check up my item status 
Report DOA item 
Return item